The fast, easy way to keep your dog home, safe and well-behaved!
The Smart Dog Basic Contain 'N' Train System can be quickly installed using common household tools. When installed, it provides a humane and effective way to keep your dog in the yard and out of areas that you want to keep pet free.
With Contain 'N' Train technology, you can reinforce basic commands from up to 150 yards away. You can even use the hand-held transmitter for behavior control outside of your containment boundaries!
Quick Start Guide
Step 1: Design Your Fence
Have the local utility companies mark your underground lines. On a sheet of paper, draw your house and yard. Draw a line around your property that represents the containment area for your dog.
Step 2: Install the Wall-Mount Transmitter
Most people find that the inside of an exterior wall of a garage or basement is ideal. From the sample layouts included, you can see the twisted wire running from the house attaches directly to the transmitter.
Step 3: Layout the Fence Wire
Run the containment wire around the property as outlined in your plan.
Step 4: Final Connections
Splice the containment loop wires to the twisted wire using the supplied waterproof splices. Connect the other end of the twisted wire to the wall-mount transmitter. Plug the AC adapter, connect it to the transmitter and turn it on. The red light should illuminate on the transmitter indicating a successful loop.
Step 5: Power Up
For all systems, install batteries positive side out. For Contain 'N' Train systems, please refer to the "Match Receiver" section of the guide.
Step 6: Test Your Fence
Set your Field Width Alignment Knob to the nine o'clock position. Using the supplied test light, walk the dog's collar up to the fence wire. Note: For Contain 'N' Train System collar must be set to containment. Listen for the warning tone and look for the test light to light. Try a number of different places around the fenced area, in order to verify the range is consistent.
Step 7: Bury Fence Wire
Dig the trench three inches deep with a flat edge spade. Or, it is faster to use a gas-powered edger. Digging the trench at an angle helps keep the wire in the ground as you place it. Place flags at edge of selected boundary field, where the warning tone is first heard not at the wire.
Train Your Dog
Watch the training video and follow the training steps outlined in the separate Training and Troubleshooting Guide. You may see your dog respond immediately to the training, however continue to follow the enclosed Training Guide to fully train your dog. The convenience that your new fence offers plus the added safety for your dog are well worth the time invested.
Free Professional Training Support
Additional behavior or training issues? Looking for the best way to get a well-behaved dog? Just call the Innotek Free Professional Training Support hotline at 1-800-364-3362 and speak with the professionals at Dogstar Training.
Smart Dog In-Ground Pet Fencing System
Models SD-2000, SD-2050, SD-3000, SD-3100
The Collar Receiver
The collar receiver is attached to a nylon collar strap that your dog will wear. The collar receiver administers the warning tone and correction should your dog attempt to leave the yard.
Fitting the Collar on Your Dog
The collar strap should fit snugly toward the top of your dog's neck with the collar receiver box on the bottom of the neck. You should be able to get one finger between the collar strap and your dog's neck. The contact points must make contact with the dog's skin for proper operation. A little hair thinning may be required.
The Hand-Held Transmitter (SD-3000, 3100 only)
The transmitter has four preset levels of stimulation. Button 1 delivers the mildest level and button 4 the most intense. The collars will stimulate for as long as you hold the button down (ten seconds max).
When your system is set to the dual Contain and Train mode, the collar has a fence release mode. If you press and hold the PROGRAM button, you will hear a tone coming from the collar. The fence will be disabled for 20 seconds before resuming normal function.
The GOOD tone and BAD tone buttons are located on the front of the transmitter. When the GOOD button is pressed a reward tone sounds and can be followed up with praise or treats to reinforce the proper behavior. The BAD button is pushed to warn the pet prior to using any of the stimulation buttons.
Operating Modes (SD-3000 & SD-3100 Only)
Your Contain 'N' Train System can operate in three different modes. These different modes are indicated by the light status on the collar receiver.
Containment Mode Only: No Light
The collar will only work with the containment portion of your system. This is the default mode after batteries are installed. To conserve battery life, it is best to keep the collar in containment mode only when the training system is not in use.
Training Mode Only: Green Blinking Light
The collar will only respond to the hand-held training transmitter.
Contain and Train Mode: Alternating Red and Green Lights
This mode enables both the training and containment functions of your system.
Low battery status is indicated by a slow red blinking light. New batteries
Invisible Technologies offers several product exchange options during the warranty period. If service is required, call 1-800-826-5527 to discuss the service plan that best serves your needs. Costs are dependent on the processing time and the desired shipping options. Please do not return this product to your retailer.
After one year from date of original retail purchase, Innotek will repair, replace, or upgrade your product at a fixed rate based on the component.
Invisible Technologies, Inc., shall not be liable or responsible for any incidental or consequential damages resulting from the use of the product or caused by any defect, failure or malfunction of the product, whether a claim is based upon warranty, contract, negligence or otherwise.
Internet Price: $249.99 Today's Price: $149.95 (Save 40%)
Shop All Products By Innotek
Usually Leaves Warehouse in 5-7 Business Days | More Shipping Info
$49.99 to $139.95